The day has finally arrived. The stars aligned and the fridge has been relocated. My biggest obstacle to removing the main wall has been eliminated. Gosh I’m nervous. I’m removing a main wall. Eeeks!
Enough of that. Let’s talk what happened this week. I soldered for the first time. Soldered a faucet. Then I made a sink and a counter and TA DA! Bathroom is now fully functional again!
A bit about soldering, it’s not that hard. It seems hard. I procrastinated on it. Then I did it and it was so easy I had no issues at all. This is a first try faucet.
Entirely hand made by moi! Allow me to show you how:
Whilst the kids were supposed to be sleeping I gathered my supplies. I cut the pipe to the necessary sizes, cleaned all of the fittings, donned gloves and began.
I put a small amount of flux on the inside of my fitting and the outside of the pipe and put them together.
Then, over a small flame, heat the fitting from the bottom. You’ll know the metal has reached the correct temperature when the solder melts within 2 seconds of touching the pipe.
You’ll see the solder get sucked into the crevice. I put on a bit much my first few solders but with time I began to figure out the perfect amount.
Thicker fittings take about a minute and a half to reach temperature. The regular copper fittings about a minute.
The pipe that you aren’t soldering, but are holding on to, gets HOT. So do be sure you are wearing thick gloves for this.
They really aren’t that sneaky. They think they are though.
You can polish up your finished faucet by simply smearing flux on, heating it and then wiping it off with a cloth.
Now, on to the sink I made. I bought a bucket at the farm store. A beautiful bucket. I arranged it just so, then marked the bottom as to where I needed to drill the hole.
Then I gathered what I needed to install the drain onto my new sink.
I bought a basic sink drain fitting, some plumbers putty and some plumbers caulk. Couldn’t be more basic. Put a ring of putty around the drain fitting, screw it on, caulk it and you’re done.
It’s GORGEOUS!!!!!!!! I have a burlap skirt that just needs a few staples to cover the front of the sink. It’s country perfect! Oh I should add we just shark bite’d it on to the old pex pipe. Super easy installation.
I was simply waiting for the bathroom sink so I could move the fridge. I attached the ice maker water tubing through the wall on to the bathroom sink. No leaks, fridge fits, it’s a dream come true!
Had time to stain the pantry shelves,
Fly a kite,
And admire the pantry shelves.
What’s next? Well other than the details, like doors on the pantry and finishing the plank wall that is going to be the last pantry wall, well this:
This hideous wall.
The entire thing. It’s all going to go. A giant island will take it’s place. A glorious, giant island. Oh the vision I have for it is so strong. I’ll be able to move around the kitchen better what with kids and dogs constantly observing and attempting to assist me. I’ll be more connected with the kids while I do daily tasks such as cooking and dishes. We’ll have a lovely counter top eat in section. I just know that this island is going to bring the family closer. So long as Husband can survive the destruction first.
with a 1:1 ratio and plopped a glob on to start smearing. Wow. No one told me how anxious that could make a person. It didn’t seem to be sticking all that well to the laminate and I was having SERIOUS doubts about this decision. However, I persevered and did 3 coats.
is supposed to be food safe. I simply didn’t want to pay that much. Yes, I’m that cheap. Plus I wasn’t sure how this was going to go down so…… I don’t regret my decision (so far). I did 6 coats of sealant.
. Also, it’s hooked into the water supply to the sink. We’ve had it about 2 years now and I’ll never go back!!!!! I don’t think our dogs want to go back either.
